{ "apiVersion": 1, "kind": "work-order", "purpose": "Taking the firearm apart for a job such as refinishing, and putting it back together to specification.", "firearm": { "slug": "cz-p-10-c", "name": "CZ P-10 C", "manufacturer": { "id": "cz", "name": "Česká zbrojovka (CZ)" }, "category": "pistol", "action": "striker-fired-short-recoil", "calibers": [ "9x19mm Parabellum", ".40 S&W" ], "alsoKnownAs": [ "P-10 Compact", "P-10 F", "P-10 S" ], "coversAlso": [ "CZ P-10 F", "CZ P-10 S", "CZ P-10 M" ], "page": "firearms/cz-p-10-c.html", "bundle": "api/v1/firearms/cz-p-10-c.json", "lastUpdated": "2026-10-29" }, "notices": [ "Česká zbrojovka (CZ) limits owner disassembly: Field strip: slide off the frame via the disassembly plate, recoil spring and barrel out of the slide; plus magazine disassembly.", "This work order is written for the CZ P-10 C. It is reported to cover CZ P-10 F; CZ P-10 S; CZ P-10 M — if the firearm on the bench is one of those, check the torque notes: values do not always carry over." ], "disclaimer": { "headline": "Read this before you use anything here.", "points": [ "This is a guide, not an authority. Entries are compiled from manufacturer manuals, technical manuals, published references, and community knowledge. Some of it comes from sources that are not authoritative, and some of it may simply be wrong.", "Always consult the manufacturer's manual for your specific firearm and serial-number range. Manufacturers change designs mid-production without renaming the model. The manual that shipped with your firearm outranks anything on this site.", "Consult a licensed gunsmith for anything beyond routine field stripping and cleaning, for any firearm you are unsure about, and for any procedure marked as gunsmith-recommended here.", "Treat every firearm as loaded. Verify it is unloaded, with the magazine removed and the chamber physically and visually checked, before any procedure in this database. Point it in a safe direction the entire time.", "Disassembly can damage a firearm or injure you. Springs are under tension, parts can launch, and reassembling a firearm incorrectly can make it unsafe to fire in a way that is not obvious from the outside. If a reassembled firearm does not pass a function check, stop and see a gunsmith.", "Torque values are shown in two groups. Values from the manufacturer or the issuing military are shown as such, with the document they came from. Values reported by anyone else — parts makers, gunsmithing publishers, articles, forums — are shown separately with who said them, how reliable that source is, and their exact words. Those are not specifications. Confirm any torque value with the manufacturer or a licensed gunsmith before relying on it.", "Nothing here is legal advice. Firearms law varies by country, state, and city, and some modifications or configurations are regulated or prohibited. You are responsible for knowing and following the law where you are.", "No warranty of any kind. Contributors and maintainers accept no liability for damage, injury, or loss arising from use of this material." ], "page": "disclaimer.html", "legal": { "summary": "Legal notice: this material is third-party information compiled from sources of varying reliability and is provided for general informational and educational purposes only. It is not gunsmithing, technical, safety or legal advice, it is not verified or endorsed by any manufacturer, and it must not be taken as fact. Any work on a firearm beyond the routine field stripping described in its own owner's manual should be performed only by a licensed and insured gunsmith. You use this material entirely at your own risk. Fundamental Build LLC and the project's contributors make no warranty of any kind and accept no liability for death, injury, damage or loss arising from its use. Full terms: LEGAL.md.", "page": "legal.html", "notice": "https://github.com/Fundamental-build-LLC/Pew-Takedown/blob/main/LEGAL.md" } }, "sourcing": { "confidence": "high", "verification": "manufacturer-manual-verified" }, "manufacturerDisassembly": { "status": "limited", "limit": "Field strip: slide off the frame via the disassembly plate, recoil spring and barrel out of the slide; plus magazine disassembly.", "statement": "CZ says no further disassembly is needed for routine maintenance, firing-pin cleaning should be entrusted to a competent gunsmith, and no further disassembly of the pistol is recommended.", "source": { "title": "CZ P-10 Instruction Manual", "publisher": "Česká zbrojovka a.s. Uherský Brod", "reliability": "primary", "url": "https://czubstrapiwebsitestorage.blob.core.windows.net/strapi-global/assets/735342000431_CZ_P_10_03_2026_en_es_cs_de_fr_ce7c84bf09.pdf", "page": "9", "pdfPage": 10, "pageUrl": "https://czubstrapiwebsitestorage.blob.core.windows.net/strapi-global/assets/735342000431_CZ_P_10_03_2026_en_es_cs_de_fr_ce7c84bf09.pdf#page=10", "quote": "CAUTION: No further disassembly of your pistol is recommended. Should your pistol require adjustment or repair be sure the task is entrusted to a competent gunsmith!" } }, "recalls": [], "shopTier": { "tier": 1, "group": "pistol", "rating": "Pew-Takedown editorial rating (1 easy – 3 hardest), not the manufacturer's", "reason": "51 line items in CZ's P-10 family list, but the rows include three backstraps, seven firing-pin sub-parts and version-only parts with the magazine as one row, so it is Glock-scale; a Glock-pattern pinned striker frame with no documented spring-held-while-pinning trap beyond putting the trigger to the rear before the slide goes on. Rated alongside the Glock, on thin evidence.", "confidence": "low", "partCount": { "value": 51, "kind": "line-items", "covers": "Complete pistol (magazine as one row); our transcribed parts list = single CZ P-10 family 'LIST OF PARTS' (English) for P-10 C, F, S, OR and suppressor-ready versions; rows marked * vary by version…", "basis": "manufacturer-parts-list", "source": { "title": "CZ P-10 Instruction Manual", "publisher": "Česká zbrojovka a.s. Uherský Brod", "reliability": "primary", "url": "https://czubstrapiwebsitestorage.blob.core.windows.net/strapi-global/assets/735342000431_CZ_P_10_03_2026_en_es_cs_de_fr_ce7c84bf09.pdf", "page": "12", "pdfPage": 13, "pageUrl": "https://czubstrapiwebsitestorage.blob.core.windows.net/strapi-global/assets/735342000431_CZ_P_10_03_2026_en_es_cs_de_fr_ce7c84bf09.pdf#page=13", "quote": "46 Rear sight" } }, "painPoints": [ { "issue": "The slide only goes back on with the trigger pulled to the rear, otherwise the frame hits the trigger bar protrusion.", "during": "reassembly", "source": { "title": "CZ P-10 Instruction Manual", "publisher": "Česká zbrojovka a.s. Uherský Brod", "reliability": "primary", "url": "https://czubstrapiwebsitestorage.blob.core.windows.net/strapi-global/assets/735342000431_CZ_P_10_03_2026_en_es_cs_de_fr_ce7c84bf09.pdf", "page": null, "pdfPage": null, "pageUrl": null, "quote": "Before reassembling the slide on the frame, the trigger must be put to the rear (pulled) position to prevent the frame colliding with the protrusion on the trigger bar." } }, { "issue": "CZ sends firing-pin (striker) cleaning and disassembly to a competent gunsmith.", "during": "both", "source": { "title": "CZ P-10 Instruction Manual", "publisher": "Česká zbrojovka a.s. Uherský Brod", "reliability": "primary", "url": "https://czubstrapiwebsitestorage.blob.core.windows.net/strapi-global/assets/735342000431_CZ_P_10_03_2026_en_es_cs_de_fr_ce7c84bf09.pdf", "page": null, "pdfPage": null, "pageUrl": null, "quote": "it is advisable to also disassemble magazine and to entrust the pistol to a competent gunsmith for the firing pin cleaning." } } ], "minutes": { "strip": 20, "rebuild": 25, "basis": "estimated", "note": "Estimate for an experienced tech with the right tools, detail strip to coatable parts (slide internals, frame pins, trigger group, sights) and rebuild to a function-checked gun; scale used across pistols: Glock-pattern 15/20 min, other strikers 20-30/25-40, DA/SA hammer guns 30-35/45-50, Hi-Power, Colt 1903 and Mark 23 40-45/60-75. Glock-pattern pinned frame with steel inserts left in place;", "source": null }, "stripScope": [ { "assembly": "Slide", "removes": [ "slide cover", "firing pin assembly (firing pin, spring holders, case, automatic safety and spring)", "extractor, pin and spring", "rear sight and screw", "front sight and screw" ] }, { "assembly": "Barrel", "removes": [ "barrel", "recoil spring" ] }, { "assembly": "Frame", "removes": [ "back strap and pin", "trigger bar pin, trigger and trigger bar", "trigger bar disconnector and spring", "trigger safety and pin", "slide stop and spring", "disassembly plate, retainer and spring", "magazine catch, plug, spring and pin" ] }, { "assembly": "Left in place", "removes": [ "front and rear steel inserts and their coiled pins" ] } ], "hardware": { "pins": 14, "springs": 13, "detents": 0, "basis": "counted from the manufacturer's parts list (one per key number unless a quantity is given)" }, "specialTools": [ { "tool": "Small pin punch", "usedFor": "Frame and trigger bar pins" } ], "fitOnRebuild": [ { "check": "Trigger to the rear before the slide goes on", "why": "Otherwise the frame collides with the trigger bar protrusion", "source": { "title": "CZ P-10 Instruction Manual", "publisher": "Česká zbrojovka a.s. Uherský Brod", "reliability": "primary", "url": "https://czubstrapiwebsitestorage.blob.core.windows.net/strapi-global/assets/735342000431_CZ_P_10_03_2026_en_es_cs_de_fr_ce7c84bf09.pdf", "page": null, "pdfPage": null, "pageUrl": null, "quote": "Before reassembling the slide on the frame, the trigger must be put to the rear (pulled) position to prevent the frame colliding with the protrusion on the trigger bar." } }, { "check": "Sight position / re-zero", "why": "Drift or pressed sights moved for coating shift point of impact unless witness-marked and returned to the same spot", "source": null }, { "check": "Full function check (trigger reset, safeties, slide lock-back, drop of striker/hammer only on trigger)", "why": "Standard after any fire-control strip; confirms springs and sears went back correctly", "source": null } ], "assessed": "2026-10-29" }, "videos": [ { "title": "How to Clean a CZ Pistol", "url": "https://www.youtube.com/watch?v=26FnoCcNUqc", "platform": "youtube", "embedUrl": null, "shows": [ "field-strip", "cleaning", "maintenance", "reassembly" ], "appliesTo": "CZ handguns (description: 'disassemble, oil, and clean a CZ handgun')", "published": "2021-10-27", "note": null, "channel": { "id": "UC3y6sVNuGbim-zRTMalhIaA", "name": "czusafirearms", "url": "https://www.youtube.com/@czusafirearms", "owner": "CZ-USA (US subsidiary)" }, "accessed": "2026-10-15" }, { "title": "CZ P-10 SAFETY FEATURES", "url": "https://www.youtube.com/watch?v=apbfefFHPZo", "platform": "youtube", "embedUrl": null, "shows": [ "operation" ], "appliesTo": "CZ P-10 series", "published": "2026-06-24", "note": null, "channel": { "id": "UCbdPQRXAzqkD0VFwEwmsgqQ", "name": "CZ Firearms", "url": "https://www.youtube.com/@CZ_Firearms", "owner": "Česká zbrojovka a.s. (Czech Republic)" }, "accessed": "2026-10-15" }, { "title": "How to Change Backstraps on a CZ Pistol", "url": "https://www.youtube.com/watch?v=uhNnKkr8WjE", "platform": "youtube", "embedUrl": null, "shows": [ "adjustment" ], "appliesTo": "CZ pistols with interchangeable backstraps (thumbnail shows an OD-green P-10-type pistol)", "published": "2022-06-10", "note": null, "channel": { "id": "UC3y6sVNuGbim-zRTMalhIaA", "name": "czusafirearms", "url": "https://www.youtube.com/@czusafirearms", "owner": "CZ-USA (US subsidiary)" }, "accessed": "2026-10-15" } ], "configurations": [], "tools": [], "phases": [ { "id": "clear", "title": "Clear and make safe", "steps": [ { "n": 1, "instruction": "Point the muzzle in a safe direction and keep your finger off the trigger." }, { "n": 2, "instruction": "Press the magazine release and remove the magazine.", "partsFreed": [ "Magazine" ] }, { "n": 3, "instruction": "Retract the slide fully to eject any chambered round and lock it open." }, { "n": 4, "instruction": "Visually inspect the chamber and magazine well, then physically feel the chamber to confirm it is empty.", "warning": "Look and feel. Both, every time." }, { "n": 5, "instruction": "Remove all live ammunition from the work area." } ], "videos": [] }, { "id": "disassemble", "title": "Disassemble", "videos": [ { "title": "How to Clean a CZ Pistol", "url": "https://www.youtube.com/watch?v=26FnoCcNUqc", "platform": "youtube", "embedUrl": null, "shows": [ "field-strip", "cleaning", "maintenance", "reassembly" ], "appliesTo": "CZ handguns (description: 'disassemble, oil, and clean a CZ handgun')", "published": "2021-10-27", "note": null, "channel": { "id": "UC3y6sVNuGbim-zRTMalhIaA", "name": "czusafirearms", "url": "https://www.youtube.com/@czusafirearms", "owner": "CZ-USA (US subsidiary)" }, "accessed": "2026-10-15" } ], "procedures": [ { "procedure": "field-strip", "title": "Field Strip", "level": "field-strip", "configuration": false, "steps": [ { "n": 1, "instruction": "Complete the Clear and Make Safe procedure and remove the magazine. The manual is explicit that the pistol must not be disassembled with the magazine inserted." }, { "n": 2, "instruction": "Confirm there is no cartridge in the chamber.", "warning": "The manual states this in capitals. Look and feel — do not rely on memory." }, { "n": 3, "instruction": "With the muzzle in a safe direction, release the slide forward, pull the trigger, and make sure the trigger stays in the rear position.", "warning": "The pistol will dry fire. This step is only safe on a confirmed empty chamber.", "tip": "The trigger must stay back. The slide will not come off a forward trigger." }, { "n": 4, "instruction": "Grasp the frame in your palm and use the fingers of that same hand to grip the rear of the slide from the top. Move the slide back by no more than 5 mm.", "tip": "5 mm, not locked open. Pulling it further defeats the takedown." }, { "n": 5, "instruction": "With your other hand, push the disassembly plate downwards until it stops.", "tip": "This is the takedown plate at the front of the frame, not a slide stop." }, { "n": 6, "instruction": "Release the pressure on the slide and run it forward off the frame.", "partsFreed": [ "Slide assembly" ] }, { "n": 7, "instruction": "Remove the recoil spring from the slide, then the barrel.", "warning": "The recoil spring assembly is under tension.", "partsFreed": [ "Recoil spring assembly", "Barrel" ] }, { "n": 8, "instruction": "Stop here for routine maintenance. The manual directs firing pin cleaning to a competent gunsmith." } ] } ] }, { "id": "refinish", "title": "Refinish", "components": [ { "name": "Slide assembly", "procedure": "field-strip", "level": "field-strip", "step": 6 }, { "name": "Recoil spring assembly", "procedure": "field-strip", "level": "field-strip", "step": 7 }, { "name": "Barrel", "procedure": "field-strip", "level": "field-strip", "step": 7 } ], "manufacturerPartsList": { "parts": 51, "scope": "Single CZ P-10 family list (English section) for all versions in the manual (P-10 C, F, S, OR, suppressor-ready); rows marked * vary by version or are absent. No separate P-10 C list. CS/DE/ES/FR copies omitted." }, "partsDiagrams": [], "materials": [ { "component": "Frame", "material": "fiberglass-reinforced polymer", "finish": null, "appliesTo": null, "note": null, "source": { "title": "CZ P-10 C", "publisher": "CZ-USA", "reliability": "primary", "url": "https://cz-usa.com/product/cz-p-10-c/", "page": null, "pdfPage": null, "pageUrl": null, "quote": "Material … Durable, fiberglass-reinforced polymer frame" } }, { "component": "Frame", "material": "Fiberglass-reinforced polymer", "finish": null, "appliesTo": "CZ P-10 C (SKU 91531), 'Variants and tech specs' table", "note": null, "source": { "title": "CZ P-10 C", "publisher": "CZ-USA", "reliability": "primary", "url": "https://cz-usa.com/product/cz-p-10-c/", "page": null, "pdfPage": null, "pageUrl": null, "quote": "Frame material … Fiberglass-reinforced polymer" } } ], "note": "The components the procedures above separate. Coating, masking and cure are outside this database; follow your coating system's instructions. A part the manufacturer marks \"factory fit\" should not be swapped or reworked." }, { "id": "reassemble", "title": "Reassemble", "videos": [ { "title": "How to Clean a CZ Pistol", "url": "https://www.youtube.com/watch?v=26FnoCcNUqc", "platform": "youtube", "embedUrl": null, "shows": [ "field-strip", "cleaning", "maintenance", "reassembly" ], "appliesTo": "CZ handguns (description: 'disassemble, oil, and clean a CZ handgun')", "published": "2021-10-27", "note": null, "channel": { "id": "UC3y6sVNuGbim-zRTMalhIaA", "name": "czusafirearms", "url": "https://www.youtube.com/@czusafirearms", "owner": "CZ-USA (US subsidiary)" }, "accessed": "2026-10-15" } ], "procedures": [ { "procedure": "reassembly", "title": "Reassembly", "configuration": false, "steps": [ { "n": 1, "instruction": "Set the barrel into the inverted slide and seat it fully forward." }, { "n": 2, "instruction": "Seat the recoil spring assembly in the cut in the barrel lug and press it down into the slide channel." }, { "n": 3, "instruction": "Before putting the slide back on, pull the trigger to the rear position and leave it there.", "warning": "The manual requires this. With the trigger forward the frame collides with the protrusion on the trigger bar and you can damage the pistol forcing it." }, { "n": 4, "instruction": "Set the slide onto the frame rails and push it rearward until it seats. The disassembly plate returns to its locked position on its own." }, { "n": 5, "instruction": "Rack the slide several times and perform the function check." } ], "instruction": null } ] }, { "id": "torque", "title": "Torque", "coverage": "sourced", "manufacturer": [ { "fastener": "Reflex sight mounting plate screws", "appliesTo": "Optics-ready P-10 models", "qualifier": "exact", "value": 1.3, "valueMax": null, "unit": "N-m", "converted": { "value": { "N-m": 1.3, "in-lb": 12, "ft-lb": 0.96 }, "valueMax": null }, "sequence": "This is the adapter plate. For the reflex sight itself, CZ defers to the sight maker's instructions.", "threadlocker": "Loctite 243 or equivalent, left to cure per its maker's instructions", "source": { "title": "CZ P-10 Instruction Manual", "publisher": "Česká zbrojovka a.s. Uherský Brod", "reliability": "primary", "url": "https://czubstrapiwebsitestorage.blob.core.windows.net/strapi-global/assets/735342000431_CZ_P_10_03_2026_en_es_cs_de_fr_ce7c84bf09.pdf", "page": "8", "pdfPage": 9, "pageUrl": "https://czubstrapiwebsitestorage.blob.core.windows.net/strapi-global/assets/735342000431_CZ_P_10_03_2026_en_es_cs_de_fr_ce7c84bf09.pdf#page=9", "quote": "To mount the plate under the reflex sight, we recommend using thread glue (e.g. Loctite 243) and tightening the screws to 1.3 Nm." } } ], "reported": [ { "fastener": "Optic adapter plate mounting screws (Holosun RMR plate for CZ P-10 OR)", "appliesTo": "CZ P-10 OR series with HOLOSUN adapter plate for RMR footprint (407C/507C/508T/SRO)", "qualifier": "exact", "value": 1.4, "valueMax": null, "unit": "N-m", "converted": { "value": { "N-m": 1.4, "in-lb": 12, "ft-lb": 1 }, "valueMax": null }, "sequence": null, "threadlocker": null, "source": { "title": "Adapter plate for RMR on CZ P10 OR and CZ Shadow 2 OR (product page)", "publisher": "HOLOSUN Europe (holosun.eu, operated by Picotronic GmbH, HOLOSUN European distributor)", "reliability": "secondary", "url": "https://www.holosun.eu/en/p/70189667", "page": null, "pdfPage": null, "pageUrl": null, "quote": "Tightening torque recommended: 1,4 Nm" } }, { "fastener": "Optic adapter plate mounting screws (Holosun RMR plate for CZ P-10 OR)", "appliesTo": "CZ P-10 OR series with HOLOSUN adapter plate for RMR footprint (407C/507C/508T/SRO)", "qualifier": "maximum", "value": 1.7, "valueMax": null, "unit": "N-m", "converted": { "value": { "N-m": 1.7, "in-lb": 15, "ft-lb": 1.3 }, "valueMax": null }, "sequence": null, "threadlocker": null, "source": { "title": "Adapter plate for RMR on CZ P10 OR and CZ Shadow 2 OR (product page)", "publisher": "HOLOSUN Europe (holosun.eu, operated by Picotronic GmbH, HOLOSUN European distributor)", "reliability": "secondary", "url": "https://www.holosun.eu/en/p/70189667", "page": null, "pdfPage": null, "pageUrl": null, "quote": "tightening torque Maximum: 1,7 Nm" } }, { "fastener": "Red-dot optic mounting screws (6-32 flat head, supplied) into EGW rear-dovetail sight mount", "appliesTo": "CZ P-10 C / P-10 F (non-optics-ready) with the EGW 'Trijicon RMR / SRO, Holosun 407c / 507c Mount for CZ P10C / P10F / P10S' (replaces the rear sight; for Trijicon RMR/SRO, Holosun 407C/507C footprint", "qualifier": "exact", "value": 15, "valueMax": null, "unit": "in-lb", "converted": { "value": { "N-m": 1.7, "in-lb": 15, "ft-lb": 1.2 }, "valueMax": null }, "sequence": "Remove the rear sight, install the EGW mount in the dovetail, tighten the set screw if applicable, place the optic on the mount, then apply blue Loctite and torque the optic screws.", "threadlocker": "Blue Loctite on the provided mounting screws (EGW instructions)", "source": { "title": "Trijicon RMR / SRO, Holosun 407c / 507c Mount for CZ P10C / P10F / P10S (EGW product page, installation instructions section)", "publisher": "Evolution Gun Works (EGW)", "reliability": "secondary", "url": "https://egwguns.com/trijicon-rmr-sro-holosun-407c-507c-mount-for-cz-p10c-p10f", "page": null, "pdfPage": null, "pageUrl": null, "quote": "Torque mounting screws to 15in/lbs" } }, { "fastener": "Red-dot optic mounting screws (supplied) into EGW rear-dovetail sight mount (Docter/Venom/Viper/FastFire footprint)", "appliesTo": "CZ P-10 C / P-10 F (non-optics-ready) with the EGW 'CZ P10C & P10F Red Dot Mount | Fits Vortex Venom, Viper & Burris FastFire | EGW' (replaces the rear sight)", "qualifier": "exact", "value": 15, "valueMax": null, "unit": "in-lb", "converted": { "value": { "N-m": 1.7, "in-lb": 15, "ft-lb": 1.2 }, "valueMax": null }, "sequence": "Remove the rear sight, install the EGW mount in the dovetail, tighten the set screw if applicable, place the optic on the mount, then apply blue Loctite and torque the optic screws.", "threadlocker": "Blue Loctite on the provided mounting screws (EGW instructions)", "source": { "title": "CZ P10C & P10F Red Dot Mount | Fits Vortex Venom, Viper & Burris FastFire | EGW (EGW product page, installation instructions section)", "publisher": "Evolution Gun Works (EGW)", "reliability": "secondary", "url": "https://egwguns.com/vortex-viper-venom-cz-p10c-p10f-sight-mount-fits-burris-fastfire-and-docter", "page": null, "pdfPage": null, "pageUrl": null, "quote": "Torque mounting screws to 15 in/lbs" } }, { "fastener": "Adapter plate and optic screws (EGW plate replacing the optics-ready cover plate)", "appliesTo": "CZ P-10 C / P-10 F / P-10 S Optics Ready with the EGW 'CZ Shadow 2/ Shadow 2 Compact / P10C / P10F / P10S Optics Ready Red Dot Mount | Fits Vortex Venom, Viper, Burris FastFire'", "qualifier": "exact", "value": 15, "valueMax": null, "unit": "in-lb", "converted": { "value": { "N-m": 1.7, "in-lb": 15, "ft-lb": 1.2 }, "valueMax": null }, "sequence": "EGW: press-fit mount; install plate, install optic, apply blue Loctite, torque screws.", "threadlocker": "Blue Loctite (EGW)", "source": { "title": "CZ Shadow 2/ Shadow 2 Compact / P10C / P10F / P10S Optics Ready Red Dot Mount | Fits Vortex Venom, Viper, Burris FastFire (EGW product page, installation instructions section)", "publisher": "Evolution Gun Works (EGW)", "reliability": "secondary", "url": "https://egwguns.com/vortex-viper-venom-fits-burris-fastfire-and-docter-sight-mount-for-cz-shadow-2-compact-shadow-2-p10c-p10f-p10s-optics-ready", "page": null, "pdfPage": null, "pageUrl": null, "quote": "Torque screws to 15 in/lbs" } } ], "notes": null }, { "id": "function-check", "title": "Function check", "checks": [ "Verify the pistol is unloaded with no magazine inserted before each check.", "Rack the slide and press the trigger. The striker should release cleanly.", "Hold the trigger to the rear, rack the slide, then release slowly and confirm the reset.", "Press the trigger again to confirm the striker releases.", "Confirm the slide locks open on an empty magazine and the magazine drops free." ], "videos": [] } ], "troubleshooting": [ { "symptom": "The slide will not go back onto the frame.", "cause": "The trigger is forward. On the P-10 the trigger must be held to the rear before the slide goes back on.", "fix": "Pull the trigger to the rear and hold it there, then fit the slide.", "damageRisk": "CZ states that with the trigger forward the frame collides with the protrusion on the trigger bar. Forcing it damages the trigger bar." }, { "symptom": "The slide stop will not come out during takedown.", "cause": "The slide is retracted too far, or not far enough. CZ specifies moving it back no more than 5 mm.", "fix": "Let the slide forward, pull the trigger so it stays rearward, then move the slide back only about 5 mm and press the disassembly plate down." } ], "sources": [ { "n": 1, "id": "cz-p10-manual", "title": "CZ P-10 Instruction Manual", "publisher": "Česká zbrojovka a.s. Uherský Brod", "reliability": "primary", "url": "https://czubstrapiwebsitestorage.blob.core.windows.net/strapi-global/assets/735342000431_CZ_P_10_03_2026_en_es_cs_de_fr_ce7c84bf09.pdf", "accessed": "2026-09-14" }, { "n": 2, "id": "holosun-europe-holosun-eu-operated-b-9f6238", "title": "Adapter plate for RMR on CZ P10 OR and CZ Shadow 2 OR (product page)", "publisher": "HOLOSUN Europe (holosun.eu, operated by Picotronic GmbH, HOLOSUN European distributor)", "reliability": "secondary", "url": "https://www.holosun.eu/en/p/70189667", "accessed": "2026-09-27" }, { "n": 3, "id": "cz-usa-specs-d10f45", "title": "CZ P-10 C", "publisher": "CZ-USA", "reliability": "primary", "url": "https://cz-usa.com/product/cz-p-10-c/", "accessed": "2026-10-03" }, { "n": 4, "id": "evolution-gun-works-egw-97c86a", "title": "Trijicon RMR / SRO, Holosun 407c / 507c Mount for CZ P10C / P10F / P10S (EGW product page, installation instructions section)", "publisher": "Evolution Gun Works (EGW)", "reliability": "secondary", "url": "https://egwguns.com/trijicon-rmr-sro-holosun-407c-507c-mount-for-cz-p10c-p10f", "accessed": "2026-10-11" }, { "n": 5, "id": "evolution-gun-works-egw-81a939", "title": "CZ P10C & P10F Red Dot Mount | Fits Vortex Venom, Viper & Burris FastFire | EGW (EGW product page, installation instructions section)", "publisher": "Evolution Gun Works (EGW)", "reliability": "secondary", "url": "https://egwguns.com/vortex-viper-venom-cz-p10c-p10f-sight-mount-fits-burris-fastfire-and-docter", "accessed": "2026-10-11" }, { "n": 6, "id": "evolution-gun-works-egw-556f8e", "title": "CZ Shadow 2/ Shadow 2 Compact / P10C / P10F / P10S Optics Ready Red Dot Mount | Fits Vortex Venom, Viper, Burris FastFire (EGW product page, installation instructions section)", "publisher": "Evolution Gun Works (EGW)", "reliability": "secondary", "url": "https://egwguns.com/vortex-viper-venom-fits-burris-fastfire-and-docter-sight-mount-for-cz-shadow-2-compact-shadow-2-p10c-p10f-p10s-optics-ready", "accessed": "2026-10-11" } ] }