← Savage Model 110 reference page · This work order as JSON ·
Work order — Savage Model 110
Taking the firearm apart for a job such as refinishing, and putting it back together to specification. Generated from the Pew-Takedown entry last updated 2026-10-29. Confidence: high.
| Work order # | |
|---|---|
| Customer | |
| Model on the bench | |
| Serial number | |
| Finish / colour | |
| Received | |
| Technician |
Before you startEducational guide only. Some information comes from non-authoritative sources. Always consult your manufacturer's manual and a licensed gunsmith. Verify your firearm is unloaded before every procedure.
- Savage Arms limits owner disassembly: Bolt out of the receiver and barreled action out of the stock (stock/action screws); bolt itself not disassembled; rear trigger-guard screw not removed.
- This work order is written for the Savage Model 110. It is reported to cover Savage Model 111, 112, 116; Savage Axis and Axis II (similar action, simpler trigger) — if the firearm on the bench is one of those, check the torque notes: values do not always carry over.
Shop difficulty: Tier 2 of 3
Few parts, but the multi-piece Savage bolt has two captive ball detents (extractor and rear baffle), a strongly compressed firing-pin spring, and a bolt head and baffles that go in one way. It is a bolt rifle with more traps than a 700. 27 parts (PARTIAL: Savage's owner-orderable list for AccuTrigger bottom-release top-load/DBM rifles; it omits barrel, receiver, barrel nut, bolt body and trigger internals). Pew-Takedown's rating, not the manufacturer's.
Bench time: strip ~35 min, rebuild ~55 min (estimate). Actual: strip ______ rebuild ______
Special tools:
- plastic bag (owners' method) — Trapping the extractor ball and spring
- torque driver — Action screws
- Savage barrel nut wrench and headspace gauges — Only if the barrel is removed (not normal for coating)
Watch for:
- The extractor sits on a 1/8 in spring-loaded ball that escapes when the extractor slides out, and is just as hard to trap going back in. (both; Gun Tests)
- The firing-pin assembly is under strong mainspring compression. Taking it apart risks losing the cocking piece and sleeve lock. (both; Gun Tests)
- The front baffle, friction washer and bolt-head retaining pin each have one correct orientation, and the rear baffle rides on its own ball and spring. (reassembly; Gun Tests)
Tools
- Bore guide — Cleaning from the breech without damaging the throat or the crown.
- Hex key or screwdriver matching the action screws — Removing the barrelled action from the stock. Not needed for routine cleaning.
- Torque wrench — Reinstalling action screws to a consistent value, which is an accuracy variable on every bolt rifle.
1. Clear and make safe
- Point the muzzle in a safe direction and keep your finger off the trigger.
- Place the safety in the on position.
- Lift the bolt handle and draw the bolt fully rearward, extracting and ejecting any chambered round.
- Unload the magazine: on a hinged floorplate rifle press the floorplate latch and let the rounds fall out; on a detachable magazine rifle remove the magazine; on a blind magazine cycle the bolt to feed and eject each round.
- Inspect the chamber and magazine well with a light and physically confirm the chamber is empty.
Warning: Look and feel. Both, every time. - Remove all live ammunition from the work area.
2. Disassemble
Manufacturer's video: Bolt Removal: Savage Centerfire Bottom Bolt Release (SavageAccuracy (Savage Arms))
https://www.youtube.com/watch?v=oKw8YVFw2zM
Bolt Removal: Savage Centerfire Thumb Sear Release (SavageAccuracy (Savage Arms))
https://www.youtube.com/watch?v=PNMubiLpnp8
Stock Removal: Savage Bolt Action (SavageAccuracy (Savage Arms))
https://www.youtube.com/watch?v=IjHzcwz_2Bk
Field Strip
- Complete the Clear and Make Safe procedure. There must be no ammunition in the chamber or the magazine — look and feel, do not assume.
- With the muzzle pointed in a safe direction, move the safety forward to the SAFETY OFF — READY TO FIRE position. The bolt will not come out with the safety on.
Warning: The rifle is now off safe. Muzzle discipline is all you have left. - Lift the bolt handle and pull the bolt fully to the rear.
- With no ammunition in the rifle, pull the trigger fully rearward and hold it there.
Warning: Removing the bolt from this rifle requires pulling the trigger. The manual says so in as many words. Verify the chamber and magazine are empty, look and feel, and point the muzzle somewhere a round would not matter before your finger goes near the trigger. - Push the cocking indicator — also called the side bolt release — as far down as it will go.
Tip: On rifles with a bottom bolt release the lever is in front of the trigger instead; the trigger pull is required either way. - Grasping the bolt handle, pull the bolt assembly fully rearward until it clears the receiver, taking care not to hit the stock.
Tip: If it binds or stops, the trigger is not held fully rearward or the release is not pushed all the way down. Do not force it. - Clean the bore from the breech using a bore guide, and clean the bolt face, lugs, and chamber.
Remove the Barrelled Action from the Stock
- Verify the rifle is unloaded and remove the bolt and magazine.
- Remove the action screws from the bottom of the stock, noting which screw came from which hole.
Tip: They are often different lengths. - Lift the barrelled action out of the stock.
3. Refinish
The components the procedures above separate. Coating, masking and cure are outside this database; follow your coating system's instructions. A part the manufacturer marks "factory fit" should not be swapped or reworked.
| Component separated | Out | Coated | Back in |
|---|---|---|---|
| Bolt assembly | |||
| Action screws | |||
| Floorplate or magazine assembly | |||
| Stock |
| Component | Material | Factory finish | Source |
|---|---|---|---|
| Stock 110 Hunter (all listed SKUs, e.g. 55649) | Synthetic | Gray | [6] |
| Barrel 110 Hunter (all listed SKUs, e.g. 55649) | — | Matte black | [6] |
| Receiver 110 Hunter (all listed SKUs, e.g. 55649) | — | Black | [6] |
The manufacturer's full parts list (27 parts) is on the reference page.
4. Reassemble
Manufacturer's video: Rear Baffle Installation: Savage Model 110 and 12/112 (SavageAccuracy (Savage Arms))
https://www.youtube.com/watch?v=Rks3pO5GhSw
Remove the Barrelled Action from the Stock
- To reinstall, seat the action in the stock, start both screws by hand, then tighten the front screw first and the rear second to a consistent torque.
Warning: Inconsistent action screw torque is one of the most common causes of a rifle that will not hold zero. Consult your stock maker’s specification rather than guessing.
Reassembly
- Confirm the bolt is correctly assembled and the bolt head is properly oriented.
- Align the bolt with the receiver raceway and slide it forward into the action.
- Close the bolt handle and cycle the bolt several times to confirm smooth travel and correct cocking.
- Confirm the bolt release retains the bolt when the action is opened fully.
- Perform the function check.
5. Torque
| Fastener | Specification | Sequence | Source | Applied | Init. |
|---|---|---|---|---|---|
| Action screws (front and rear) Savage 110 with polymer or wood stocks |
40 in-lb 4.5 N·m · 3.3 ft-lb |
[3] | |||
| Action screws (front and rear) Savage 110 chassis models (the FAQ row reads 'AXIS or 110 Chassis models') |
65 in-lb 7.3 N·m · 5.4 ft-lb |
[3] |
Reported by other sources — not the manufacturer
Not a manufacturer specificationConfirm with the manufacturer or a licensed gunsmith before use. Where these differ from a manufacturer value above, the manufacturer wins.
| Fastener | Reported value | Sequence | Source | Applied | Init. |
|---|---|---|---|---|---|
| Action screws (front and rear) 3rd-generation Savage short-action 10/110 centerfire rifles (center-feed, 4.40" action-screw spacing, 2006 on) in a Magpul Hunter 110 stock Reported by Magpul Industries (secondary) — not the manufacturer |
55–60 in-lb 6.2–6.8 N·m · 4.6–5 ft-lb |
Push the barreled action rearward so the recoil lug contacts the rear surface of the Recoil Lug Slot, tighten both action screws, then torque with an in-lbs wrench and 3/16" bit. 'CAUTION: Ensure you are using an in-lbs. and NOT a ft-lbs. torque wrench'. | [4] PDF p. 1 (PDF p. 1) | ||
| Front and middle action screws Savage bolt-action rifles (three action screws) in a Hogue OverMolded stock Reported by Hogue, Inc. (secondary) — not the manufacturer |
55–65 in-lb 6.2–7.3 N·m · 4.6–5.4 ft-lb |
Stand rifle on butt while applying downward pressure on barrel, tighten the front action screw first, then middle screw, etc. This better seats the recoil lug for accuracy. | [5] PDF p. 1 (PDF p. 1) | ||
| Rear (trigger guard) screw Savage bolt-action rifles (three action screws) in a Hogue OverMolded stock Reported by Hogue, Inc. (secondary) — not the manufacturer |
15 in-lb 1.7 N·m · 1.2 ft-lb |
[5] PDF p. 1 (PDF p. 1) | |||
| Action screws (front and rear) Savage SA/LA (110-pattern) in an MDT Oryx chassis Reported by MDT Sporting Goods Ltd. (Modular Driven Technologies, MDT) (secondary) — not the manufacturer |
60–65 in-lb 6.8–7.3 N·m · 5–5.4 ft-lb |
Push the action rearward against the recoil lug and torque the front action screw first, then the rear (manual p. 1: 'first torquing the front then the rear action screw'). Short action: use the supplied offset oval washer on the front screw, flipped to suit your screw spacing. | [7] PDF p. 2 (inlet-specific torque table) (PDF p. 2) | ||
| Action screws (front and rear) Savage short action (stock OEM, top bolt release) in an MDT TAC21 Gen 2 chassis Reported by MDT Sporting Goods Ltd. (Modular Driven Technologies, MDT) (secondary) — not the manufacturer |
80 in-lb 9 N·m · 6.7 ft-lb |
Start with the front screw; the front screw has an elongated washer for early/late Savage hole spacing. Forend bolts (chassis hardware) max 36 in-lb. | [8] PDF p. 3 ('TAC21 Gen 2 Chassis System Fo (PDF p. 3) | ||
| Action screws (front and rear) Savage (110-pattern) in a KRG Savage Bravo chassis Reported by Kinetic Research Group (KRG) (secondary) — not the manufacturer |
65 in-lb 7.3 N·m · 5.4 ft-lb |
Tighten alternately front/rear in increments until full torque is reached. | [9] PDF p. 1 (PDF p. 1) | ||
| Action screws (all except rear guard screw) Savage in an H-S Precision Pro-Series stock Reported by H-S Precision, Inc. (secondary) — not the manufacturer |
65 in-lb 7.3 N·m · 5.4 ft-lb |
[10] PDF p. 1, step 3 (PDF p. 1) | |||
| Rear guard screw Savage in an H-S Precision Pro-Series stock Reported by H-S Precision, Inc. (secondary) — not the manufacturer |
30–35 in-lb 3.4–4 N·m · 2.5–2.9 ft-lb |
Alternative given by the maker: 'hand tight'. | [10] PDF p. 1, step 3 (PDF p. 1) | ||
| Action screws (barreled action to UMC) Savage 110 and 110-pattern actions in a Grayboe stock with Universal Mini Chassis (UMC) Reported by Grayboe (secondary) — not the manufacturer |
45 in-lb 5.1 N·m · 3.7 ft-lb |
Install the UMC into the stock first (UMC-to-stock screws 60 in-lb), then the barreled action. | [11] p. Section 'Savage 110', Step 3 | ||
| Action screws (front and rear) Savage short action in a MasterPiece Arms BA chassis (use the supplied insert matching the action-screw spacing) Reported by MasterPiece Arms, Inc. (secondary) — not the manufacturer |
65 in-lb 7.3 N·m · 5.4 ft-lb |
Snug front then rear; torque front to 25 in-lb, then rear to 25 in-lb; then front to 65 in-lb, then rear to 65 in-lb. Always start with the front screw. Re-check at 100-125 rounds and again after 500. | [12] PDF p. 1–2, steps 9–10 (Savage Short Act (PDF p. 1) | ||
| Bolt Action Magazine Well screws (two 1/4-28 x 1/2” SHCS) Savage 110 short action in a Magpul Hunter 110 stock Reported by Magpul Industries (secondary) — not the manufacturer |
approx. 20 in-lb 2.3 N·m · 1.7 ft-lb |
Insert the magazine well until both locking tabs snap in, then hand tighten the two screws; do not overtighten. | [13] PDF p. 1 (PDF p. 1) | ||
| Action screws (front and rear) Savage Axis short action in a Magpul Hunter Lite stock Reported by Magpul Industries (secondary) — not the manufacturer |
40 in-lb 4.5 N·m · 3.3 ft-lb |
Use an in-lb (not ft-lb) torque wrench with a 3/16” bit. | [14] PDF p. 1, step 4 (PDF p. 1) |
Fit or check on rebuild
- Bolt-head pin orientation / firing pin passes through — A misoriented pin blocks the firing pin.
- Action screw torque — Affects zero.
- Re-zero sights or scope — Sights and optics come off for coating, and point of impact must be re-confirmed. This is a standard check, so no source.
6. Function check
- Verify the rifle is unloaded and the magazine is empty before each check.
- Cycle the bolt and confirm it cocks and closes fully into battery.
- With the action cocked, engage the safety and press the trigger. The firing pin must not release.
- Disengage the safety without touching the trigger. The firing pin must not release.
- Press the trigger and confirm the firing pin releases cleanly.
- Confirm the bolt release retains the bolt.
- Load dummy rounds and confirm they feed from the magazine and eject cleanly.
If any check fails, the firearm is not safe to fire. Stop and see a licensed gunsmith.
If it won't go back together
| Symptom | Cause | Fix |
|---|---|---|
| The bolt binds partway and will not clear the receiver. | The trigger is not held fully rearward, or the cocking indicator is not pushed all the way down. | With no ammunition present and the safety forward, pull the trigger fully rearward and HOLD it, push the cocking indicator down as far as it goes, then draw the bolt out. |
Sources
- Savage Arms Centerfire Rifle Manual — Models 10/110, 11/111, 14/114, 16/116 — Savage Arms, Inc. primary
https://saweb.s3.us-east-1.amazonaws.com/manuals/manual_centerfire_10_110_11_111_14_114_16_116_non_le.pdf - Savage Arms Axis Rifle Manual — Savage Arms, Inc. primary
https://saweb.s3.us-east-1.amazonaws.com/manuals/manual_centerfire_axis.pdf - What is the torque spec for my action screws? — Savage Arms (service.savagearms.com help center) primary
https://service.savagearms.com/hc/en-us/articles/214238343-What-is-the-torque-spec-for-my-action-screws - Hunter 110 Stock – Savage 110 Short Action (MAG1069) Installation Instructions — Magpul Industries secondary
https://magpul.com/media/wysiwyg/Instructions/MAG1069_Hunter_110_INSRT.pdf - OverMolded Stock for Savage Bolt Action Rifles — installation card CRD_INS_SAVAGE110_03202017 — Hogue, Inc. secondary
https://www.hogueinc.com/media/custom/upload/File-1497473149.pdf - 110 Hunter | Hunting Rifle with AccuFit | Savage Arms — Savage Arms primary
https://savagearms.com/firearms/model/110-hunter - MDT Oryx Chassis System — User Manual (13694, Version 07.14.26), attached to MDT help-centre article 'ORYX Chassis Installation Guides' — MDT Sporting Goods Ltd. (Modular Driven Technologies, MDT) secondary
https://support.mdttac.com/hc/article_attachments/51468856863892 - MDT TAC21 Gen 2 Chassis System — Owner's Manual (Tac21_Manual.pdf, 2020), attached to MDT help-centre article 'TAC 21 installation manual' — MDT Sporting Goods Ltd. (Modular Driven Technologies, MDT) secondary
https://support.mdttac.com/hc/article_attachments/360074382811 - KRG Savage Bravo Chassis — Installation Instructions (INST-BRV-SVG) — Kinetic Research Group (KRG) secondary
https://kineticresearchgroup.com/download/78615/ - H-S Precision — Instructions for the Savage Pro-Series® Stocks — H-S Precision, Inc. secondary
https://hsprecision.com/wp-content/uploads/2021/04/Savage_Instructions_ProSeries_HSPrecision.pdf - Grayboe — UMC (Universal Mini Chassis) Installation Instructions (web page) — Grayboe secondary
https://www.grayboe.com/pages/umc-installation-instructions - MasterPiece Arms BA Chassis System — Installation, Setup and Usage (rev B) — MasterPiece Arms, Inc. secondary
https://masterpiecearms.com/wp-content/uploads/2014/05/Masterpiece-Arms-BA-Chassis-System-Installation-rev-b.pdf - Magpul MAG1069 Hunter 110 Stock – Savage 110 Short Action — Instructions (092-0066-C) — Magpul Industries secondary
https://magpul.com/media/wysiwyg/Instructions/MAG1069_INSRT_Hunter_110_092-0066-C.pdf - Magpul MAG1354 Hunter Lite Stock – Savage Axis Short Action — Instructions — Magpul Industries secondary
https://magpul.com/media/wysiwyg/Instructions/MAG1354_Hunter_Lite_INSRT.pdf - Working the Savage Model 110 — Gun Tests secondary
https://www.gun-tests.com/rifles/working-the-savage-model-110/
| Reassembled and function-checked by | Date |
|---|
Educational guide only. Some information comes from non-authoritative sources. Always consult your manufacturer's manual and a licensed gunsmith. Verify your firearm is unloaded before every procedure. Full disclaimer: https://github.com/Fundamental-build-LLC/Pew-Takedown
Legal notice: this material is third-party information compiled from sources of varying reliability and is provided for general informational and educational purposes only. It is not gunsmithing, technical, safety or legal advice, it is not verified or endorsed by any manufacturer, and it must not be taken as fact. Any work on a firearm beyond the routine field stripping described in its own owner's manual should be performed only by a licensed and insured gunsmith. You use this material entirely at your own risk. Fundamental Build LLC and the project's contributors make no warranty of any kind and accept no liability for death, injury, damage or loss arising from its use. Full terms: LEGAL.md.