← All firearms · Printable work order

Taurus G3c

• easy
• Shop tier 2
• medium confidence
• Pistol
• striker fired
• polymer frame
• budget
• restrike capable

field strip ~1 min · reassembly ~2 min · detail strip ~20 min

Specifications

Model-specific safety

• Verify the chamber is empty before any takedown attempt, and confirm from your manual whether your variant requires the trigger to be pressed — the Taurus G-series has seen running changes.
• These pistols have a restrike capability: if a round does not fire, pressing the trigger again will drop the striker a second time. That is a design feature, but it also means the trigger can be live in a state where a striker pistol would not be.
• The recoil spring assembly is under tension when the slide is off.
• Some G-series pistols have a manual thumb safety and a keyed Taurus Security System lock. Identify your controls.

Under spring tension

• Recoil spring assembly

Easily lost parts

Takedown lever · Recoil spring assembly

Tools

No tools required for the field strip.

Shop difficulty

Shop tier 2 Tier 2 — moderate among pistols, for the full job: strip to the parts that get coated and put it back together working. 66 rows (incl. assembly rows, four alternate front sights and the magazine) is about 55 working parts, more than a Glock: two-piece recoil assembly with a screw, a central support and rear support carrying the restrike trigger, manual safety with a detent ball, and three spirol pins. No timing; borderline Tier 1 on difficulty, Tier 2 on parts.

Parts: 66 numbered parts ('Exploded View (G3c)' (p. 36) and 'Part List (G3c)' (p. 37), complete pistol incl. magazine; includes assembly rows (1, 2, 5, 6) and four alternate front sights.), from Taurus G3 & G3c Instruction Manual - General Safety, Operating Instructions and Limited Warranty (InDesign file dated 22 Oct 2020) — Taurus USA, p. 36–37 taurususa.com [2].

Bench time: about 20 min to strip, 30 min to rebuild (estimate). Slide (slide cap and plate, firing pin assembly and block, extractor, sights) and frame (spirol pins, central and rear supports, trigger assembly, sear, safety and detent ball, slide catch, disassembling latch); rebuild longer for the supports and safety detent.

Small parts: 17 pins, 15 springs, 0 detents or plungers (counted from the manufacturer's parts list (one per key number unless a quantity is given))

What comes off for coating

• Slide: slide cap and plate, firing pin, sleeves and springs, firing pin block and spring, extractor, pin and springs, rear sight, front sight and screw — pin punch, sight pusher
• Frame: spirol pins (2x24, 3x24, 2.5x22), central support, sleeve and trigger assembly pin, trigger, trigger bar, trigger safety and springs, rear support, sear, disconnector, ejector, manual safety, sphere and spring, slide catch and spring, disassembling latch, pin and spring, magazine release and spring — roll-pin punches

Special tools

• roll-pin punches (2, 2.5, 3 mm) — Spirol pins
• dovetail sight pusher (or brass drift and padded vise) — Removing and refitting dovetailed sights for coating

Known pain points

• Taurus recommends nothing past the field strip except by a skilled gunsmith. (both)
  Source: Taurus G3 & G3c Instruction Manual - General Safety, Operating Instructions and Limited Warranty (InDesign file dated 22 Oct 2020) — Taurus USA taurususa.com [2] — “No further disassembly is recommended unless done by a skilled gunsmith.”

Fit or check on rebuild

• Cycle the slide to check barrel/slide/frame relationship — Taurus's own post-reassembly check
  Source: Taurus G3 & G3c Instruction Manual - General Safety, Operating Instructions and Limited Warranty (InDesign file dated 22 Oct 2020) — Taurus USA taurususa.com [2] — “You should cycle the slide several times, with no magazine inserted and no rounds in the chamber, to insure that the barrel / slide / frame relationship is correct.”
• Function check: trigger reset, sear/striker engagement, safeties — Standard post-reassembly check on any pistol whose fire-control parts were removed; a mis-seated spring shows up here, not on the bench

This is Pew-Takedown's rating, not the manufacturer's. How tiers are rated. Forum reports are owners' experience, not specifications.

Procedures

Torque specifications

Notes: The manufacturer's documents give no torque value. They say: "At the same time check for any lose screws or pins. Tighten the screws and press pins back in as needed." (Taurus G3 & G3c Instruction Manual - General Safety, Operating Instructions and Limited Warranty (InDesign file dated 22 Oct 2020), p. 30 (Care and Maintenance))

Reported by other sources — not the manufacturer

Materials and factory finish

As stated by Taurus Armas. Prep, masking and cure depend on these; a polymer or aluminium part, a nitrided or anodised finish, and a blued steel part are each a different job. Variants with other finishes may exist — check the maker's page for the exact SKU on the bench.

Parts list

Transcribed from the manufacturer's parts list (Taurus G3 & G3c Instruction Manual - General Safety, Operating Instructions and Limited Warranty (InDesign file dated 22 Oct 2020) — Taurus USA, p. 36–37 taurususa.com [2]) — "Exploded View (G3c)" (p. 36) and "Part List (G3c)" (p. 37). Separate G3 list (pp. 34-35) and optic-ready mount-plate table (p. 33) omitted.. Key numbers refer to the exploded view in that document.

Function check

• Verify the pistol is unloaded with no magazine inserted before each check.
• Rack the slide and press the trigger. The striker should release cleanly.
• Hold the trigger to the rear, rack the slide, then release slowly and confirm the reset.
• Press the trigger again to confirm the striker releases.
• Confirm the slide locks open on an empty magazine and the magazine drops free.
• If fitted, confirm the manual thumb safety blocks the trigger, and that the Taurus Security System lock is in the unlocked position.

Maintenance

Lubrication points

• Frame rails where the slide rides
• Barrel hood and locking lug
• Outside of the barrel at the muzzle end
• Rear barrel lug where the recoil spring assembly bears

Cleaning notes

Light lubrication only — a thin film on the rails and barrel. Keep the striker or firing pin channel dry and free of solvent, since oil there collects fouling and causes light strikes.

Suggested inspection interval: roughly every 5000 rounds. This is a general guideline, not a manufacturer specification.

Wear parts to inspect

Recoil spring assembly · Extractor · Magazine springs and followers

Common issues

Also covers

The procedures above are reported to apply to: Taurus G2c · Taurus G3 · Taurus G3X and G3XL. Verify against the manual for your specific model.

Similar manual of arms

• Glock 19 Gen5
• Smith & Wesson M&P Shield Plus

Sourcing