← Taurus G3c reference page · This work order as JSON · Print

Work order — Taurus G3c

Taking the firearm apart for a job such as refinishing, and putting it back together to specification. Generated from the Pew-Takedown entry last updated 2026-10-29. Confidence: medium.

Shop difficulty: Tier 2 of 3

66 rows (incl. assembly rows, four alternate front sights and the magazine) is about 55 working parts, more than a Glock: two-piece recoil assembly with a screw, a central support and rear support carrying the restrike trigger, manual safety with a detent ball, and three spirol pins. No timing; borderline Tier 1 on difficulty, Tier 2 on parts. 66 parts ('Exploded View (G3c)' (p. 36) and 'Part List (G3c)' (p. 37), complete pistol incl. magazine; includes assembly rows (1, 2, 5, 6) and four alternate front sights.). Pew-Takedown's rating, not the manufacturer's.

Bench time: strip ~20 min, rebuild ~30 min (estimate). Actual: strip ______ rebuild ______

Special tools:

• roll-pin punches (2, 2.5, 3 mm) — Spirol pins
• dovetail sight pusher (or brass drift and padded vise) — Removing and refitting dovetailed sights for coating

Watch for:

• Taurus recommends nothing past the field strip except by a skilled gunsmith. (both; Taurus USA)

1. Clear and make safe

1. Point the muzzle in a safe direction and keep your finger off the trigger.
2. Press the magazine release and remove the magazine.
3. Retract the slide fully to eject any chambered round and lock it open.
4. Visually inspect the chamber and magazine well, then physically feel the chamber to confirm it is empty.
   Warning: Look and feel. Both, every time.
5. Remove all live ammunition from the work area.

2. Disassemble

Field Strip

1. Complete the Clear and Make Safe procedure and leave the slide locked to the rear.
2. Rotate the takedown lever on the frame downward until it stops.
3. Hold the slide, release the slide stop, and ease the slide forward off the front of the frame.
   Warning: Control the slide rather than letting it fly forward.
4. Lift the recoil spring assembly out of the inverted slide.
   Warning: Under spring tension.
5. Lift the barrel out of the slide.

3. Refinish

The components the procedures above separate. Coating, masking and cure are outside this database; follow your coating system's instructions. A part the manufacturer marks "factory fit" should not be swapped or reworked.

The manufacturer's full parts list (66 parts) is on the reference page.

4. Reassemble

Reassembly

1. Set the barrel into the inverted slide and seat it fully forward.
2. Seat the recoil spring assembly into the cut in the barrel lug and press it down into the slide channel.
   Tip: It seats in the lug cut, not on the barrel itself.
3. Set the slide onto the frame rails and push it rearward until it seats.
4. Return the takedown lever to its locked position.
   Warning: Confirm the takedown lever is fully returned before the pistol goes back into service.
5. Rack the slide several times and perform the function check.

5. Torque

Reported by other sources — not the manufacturer

Notes: The manufacturer's documents give no torque value. They say: "At the same time check for any lose screws or pins. Tighten the screws and press pins back in as needed." (Taurus G3 & G3c Instruction Manual - General Safety, Operating Instructions and Limited Warranty (InDesign file dated 22 Oct 2020), p. 30 (Care and Maintenance))

Fit or check on rebuild

• Cycle the slide to check barrel/slide/frame relationship — Taurus's own post-reassembly check
• Function check: trigger reset, sear/striker engagement, safeties — Standard post-reassembly check on any pistol whose fire-control parts were removed; a mis-seated spring shows up here, not on the bench

6. Function check

• Verify the pistol is unloaded with no magazine inserted before each check.
• Rack the slide and press the trigger. The striker should release cleanly.
• Hold the trigger to the rear, rack the slide, then release slowly and confirm the reset.
• Press the trigger again to confirm the striker releases.
• Confirm the slide locks open on an empty magazine and the magazine drops free.
• If fitted, confirm the manual thumb safety blocks the trigger, and that the Taurus Security System lock is in the unlocked position.

If any check fails, the firearm is not safe to fire. Stop and see a licensed gunsmith.

Sources

1. Taurus G3c Owner’s Manual — Taurus Armas S.A. primary
2. Taurus G3 & G3c Instruction Manual - General Safety, Operating Instructions and Limited Warranty (InDesign file dated 22 Oct 2020) — Taurus USA primary
   https://www.taurususa.com/wp-content/uploads/2025/05/Taurus_Manual_G3_G3c.pdf
3. Ficha Técnica — Pistola Taurus G3c T.O.R.O. 9mm (Taurus Armas) — Taurus Armas S.A. primary
   https://taurusarmas.com.br/download/detalhes/fichas-tecnicas-pistolas/arquivo/254
4. Taurus Armas S.A. — pistola g3c toro cal 9mm — Taurus Armas S.A. primary
   https://taurusarmas.com.br/pt/produtos/pistolas/pistola-g3c-toro-cal-9mm
5. Trijicon RMR / SRO, Holosun 407c / 507c Sight Mount for Glock (EGW product page, installation instructions section) — Evolution Gun Works (EGW) secondary
   https://egwguns.com/trijicon-rmr-sro-holosun-407c-507c-mount-for-glock
6. Glock Red Dot Mount | Fits Vortex Venom, Viper & Burris FastFire | EGW (EGW product page, installation instructions section) — Evolution Gun Works (EGW) secondary
   https://egwguns.com/vortex-viper-venom-glock-sight-mount-fits-burris-fastfire-and-docter

Educational guide only. Some information comes from non-authoritative sources. Always consult your manufacturer's manual and a licensed gunsmith. Verify your firearm is unloaded before every procedure. Full disclaimer: https://github.com/Fundamental-build-LLC/Pew-Takedown

Legal notice: this material is third-party information compiled from sources of varying reliability and is provided for general informational and educational purposes only. It is not gunsmithing, technical, safety or legal advice, it is not verified or endorsed by any manufacturer, and it must not be taken as fact. Any work on a firearm beyond the routine field stripping described in its own owner's manual should be performed only by a licensed and insured gunsmith. You use this material entirely at your own risk. Fundamental Build LLC and the project's contributors make no warranty of any kind and accept no liability for death, injury, damage or loss arising from its use. Full terms: LEGAL.md.