← Beretta 92FS reference page · This work order as JSON · Print

Work order — Beretta 92FS

Taking the firearm apart for a job such as refinishing, and putting it back together to specification. Generated from the Pew-Takedown entry last updated 2026-10-29. Confidence: high.

Shop difficulty: Tier 2 of 3

62 line items (73 pieces) in American Rifleman's parts legend; punch-and-screwdriver work, but the slide-mounted safety hides two captive plungers and springs that fly when the lever comes out and must be held while it goes back in, and the trigger bar spring and hammer spring are released under tension. A classic Tier 2 detail strip. 62 parts (Complete pistol incl. magazine (keys 1-62; 73 pieces counting stocks (2), stock screws (4), bushings (4), washers (4) and right safety lever spring pins (2))). Pew-Takedown's rating, not the manufacturer's.

Bench time: strip ~30 min, rebuild ~45 min (estimate). Actual: strip ______ rebuild ______

Special tools:

• Small roll-pin punches (1/16 in. and 3/32 in.) — Right safety lever pins, hammer spring cap pin, extractor pin
• Bench block — Supporting the slide while drifting the safety lever pins
• Dovetail sight pusher — Rear sight (front sight is integral)

Watch for:

• Removing the left safety lever releases the safety plunger and its spring plus the trigger bar release plunger and its spring, small captive parts that are easily lost. (both; American Rifleman (NRA))
• Reinstalling the slide safety takes three hands at once: the firing pin safety plunger and the firing pin plunger held down while the lever is rotated, with two spring-loaded detents to capture. (reassembly; Canadian Gun Nutz)
• The trigger bar spring has to be unhooked from its groove and eased out under tension, and hooked back into the trigger bar on reassembly. (both; American Rifleman (NRA))
• The hammer spring is held by a cap and spring pin; drifting the pin releases the hammer spring under tension, and the cap must be compressed again to repin it. (both; American Rifleman (NRA))

1. Clear and make safe

1. Point the muzzle in a safe direction and keep your finger off the trigger.
2. Press the magazine release and remove the magazine.
3. Retract the slide fully to eject any chambered round, and lock it open with the slide stop.
4. Inspect the chamber visually and physically. The open-top slide makes this easy — use that advantage.
   Warning: The open-slide design does not remove the need for a physical check.
5. Remove all live ammunition from the work area.

2. Disassemble

Field Strip

1. Complete the Clear and Make Safe procedure and let the slide return forward.
2. Depress the magazine release button and remove the magazine if it is not already out.
3. Hold the pistol in your right hand. With your left forefinger press the disassembly latch release button on the right side of the frame, and with your left thumb rotate the disassembly latch clockwise until it stops.
   Tip: The latch is on the left side of the frame and rotates downward and forward. The manual describes the motion as clockwise.
4. Pull the slide and barrel assembly forward off the frame, together with the locking block, recoil spring, and spring guide.
5. Press the recoil spring and spring guide slightly.
6. Lift the spring guide and recoil spring out, letting the spring stretch slowly.
   Warning: Do not let the spring go abruptly. The manual specifies easing it out under control.
7. Press the locking block plunger.
8. Take the barrel and locking block assembly out of the slide.

Disassemble the magazine

1. Unload the magazine.
2. Grasp the magazine firmly with the floorplate up and the back of the magazine tube against the palm of your hand.
3. Push down on the floorplate retainer stud in the center of the floorplate and, at the same time, slide the floorplate forward a short distance with your thumb.
   Warning: Magazine spring is under slight tension. Use care when removing magazine floorplate.
   Tip: The manual's note: to press the stud, use either the tip of a 9mm round or the barrel locking block plunger — depressing the locking block makes the plunger protrude so it can be used as a tool.
4. While keeping pressure on the magazine spring with your thumb, remove the floorplate from the magazine.
5. Remove the floorplate retainer, magazine spring and follower from the magazine tube.
6. Remove the floorplate retainer from the magazine spring.

3. Refinish

The components the procedures above separate. Coating, masking and cure are outside this database; follow your coating system's instructions. A part the manufacturer marks "factory fit" should not be swapped or reworked.

4. Reassemble

Disassemble the magazine

1. Reverse the steps of "Disassemble the magazine".

Reassemble the magazine

1. Insert the follower into the top coil of the magazine spring — the top coil is the one with an upward and forward pointing end.
   Tip: Make sure the notches on the follower and the magazine tube are on the same side.
2. Insert the magazine spring with the follower into the magazine tube.
3. Turn the magazine bottom up with its back side against the palm of your hand.
4. Attach the floorplate retainer to the bottom spring coil and center it.
   Warning: After insertion, spring tension must be maintained using the thumb. Do not place the lips of the magazine tube on a hard surface during reassembly.
5. Push and hold the magazine spring and floorplate retainer down and, at the same time, slide the floorplate over the side walls until fully seated; a click indicates it is seated.
6. Insert the magazine into the magazine well carefully until it clicks into the locked position.

Reassembly

1. Set the barrel and locking block assembly into the inverted slide, locking block down, and seat it fully forward.
2. Insert the recoil spring and guide through the spring, seat the guide into its cut in the barrel lug, and press it down into the slide.
3. Set the slide onto the frame rails from the front and push it rearward until it seats fully.
   Warning: Before placing the slide on the frame, make sure the hammer is uncocked and the firing pin block lever is down, and the decocking/safety lever is in the safe (down) position. If the hammer is cocked, lower it carefully by hand. Do not pull the trigger while placing the slide on the frame.
4. Rotate the disassembly latch lever upward until it clicks and the release button pops back out.
5. Rack the slide to confirm free travel, then perform the function check.
   Warning: If the disassembly latch is not fully rotated up, the slide can come off the frame under recoil.

5. Torque

No manufacturer torque values are recorded for this firearm.

Reported by other sources — not the manufacturer

Notes: The manufacturer's documents give no torque value. They say: "When the adjustable rear sight base is centered in the slide, lock it in position screwing the two dowels to the end, without forcing, using the Allen key supplied." (Beretta 90 Series Pistol User Manual (92/96), PDF p. 30 (adjustable rear sight, target/competition versions))

Fit or check on rebuild

• Safety/decocker function and hammer drop check — The slide safety holds two detents and the firing pin plunger; a mis-seated part leaves the decocker or firing pin block inoperative
• Disassembly latch fully rotated up — A latch not rotated fully up lets the slide come off while shooting
• Sight position / re-zero — Drift or pressed sights moved for coating shift point of impact unless witness-marked and returned to the same spot
• Full function check (trigger reset, safeties, slide lock-back, drop of striker/hammer only on trigger) — Standard after any fire-control strip; confirms springs and sears went back correctly

6. Function check

• Verify the pistol is unloaded before each check.
• With the safety/decocker in the fire position and the hammer down, press the trigger. The hammer should rise and fall in double action.
• Cock the hammer, then rotate the safety/decocking lever down. The hammer should fall to the safe position and the trigger should be disconnected.
• With the lever still down, press the trigger. Nothing should happen.
• Return the lever to fire, rack the slide, and press the trigger. The hammer should fall in single action.
• Hold the trigger back, rack the slide, release slowly for the reset, and press again.
• Confirm the slide locks open on an empty magazine and that the magazine drops free.

If any check fails, the firearm is not safe to fire. Stop and see a licensed gunsmith.

If it won't go back together

Sources

1. Beretta 90 Series Pistol User Manual (92/96) — Fabbrica d'Armi Pietro Beretta primary
   https://dam.beretta.com/content/dam/beretta-usa/user-manuals/90_Series_Manual.pdf
2. Beretta Firearms User Manuals — Fabbrica d'Armi Pietro Beretta primary
   https://www.beretta.com/en/services/beretta-services/user-manuals
3. TM 9-1005-317-10: Pistol, Semiautomatic, 9mm, M9 — U.S. Department of the Army primary
4. Beretta 92/96 Series OverMolded Rubber Grip with Finger Grooves (product page) — Hogue, Inc. secondary
   https://www.hogueinc.com/beretta-92-96-series-overmolded-rubber-grip-finger-grooves-black
5. TM 9-1005-317-10 Operator's Manual: Pistol, Semiautomatic, 9mm, M9 (reprint including Changes 1–3) — Departments of the Army, Navy and Air Force; Headquarters, Marine Corps; Commandant, Coast Guard primary
   https://archive.org/download/milmanual-tm-9-1005-317-10---operators-manual-m9-9mm-handgun/tm_9-1005-317-10_-_operators_manual_m9_9mm_handgun.pdf
6. Trijicon RMR / SRO, Holosun 407c / 507c Mount for Beretta 92 (EGW product page, installation instructions section) — Evolution Gun Works (EGW) secondary
   https://egwguns.com/trijicon-rmr-sro-holosun-407c-507c-mount-for-beretta-92
7. Beretta 92 Red Dot Mount | Fits Vortex Venom, Viper, FastFire (EGW product page, installation instructions section) — Evolution Gun Works (EGW) secondary
   https://egwguns.com/vortex-viper-venom-red-dot-sight-mount-for-beretta-92-fits-burris-fastfire-and-docter
8. Leupold DeltaPoint Pro Reflex Sight — Operating Instructions (Part #120278, artwork #120279P; English text with French translation) — Leupold & Stevens, Inc. secondary
   https://www.leupold.com/media/manuals/DeltaPoint_Pro_Manual_French_120279P.pdf
9. "U.S. Pistol, M9" Beretta Model 92FS (Exploded View) — American Rifleman (NRA) secondary
   https://www.americanrifleman.org/articles/2014/1/24/us-pistol-m9-beretta-model-92fs
10. DIY: Installing a Wilson Combat low-profile safety on a Beretta 92 — Canadian Gun Nutz anecdotal
    https://www.canadiangunnutz.com/forum/threads/diy-installing-a-wilson-combat-low-profile-safety-on-a-beretta-92.1412680

Educational guide only. Some information comes from non-authoritative sources. Always consult your manufacturer's manual and a licensed gunsmith. Verify your firearm is unloaded before every procedure. Full disclaimer: https://github.com/Fundamental-build-LLC/Pew-Takedown

Legal notice: this material is third-party information compiled from sources of varying reliability and is provided for general informational and educational purposes only. It is not gunsmithing, technical, safety or legal advice, it is not verified or endorsed by any manufacturer, and it must not be taken as fact. Any work on a firearm beyond the routine field stripping described in its own owner's manual should be performed only by a licensed and insured gunsmith. You use this material entirely at your own risk. Fundamental Build LLC and the project's contributors make no warranty of any kind and accept no liability for death, injury, damage or loss arising from its use. Full terms: LEGAL.md.